Franklin-fueling-systems T5 Series Fuel Management System Programming Guide Manual do Utilizador descarregar pdf (Página 61)

Displayed Alarm /

Warning

Device Description Recommended Actions

Line Not Learned Line Specied line not learned. Complete learn process, if any learn alarms occur follow the

proper procedure. Refer to “LS500 Auto Learn Line Leak Detection

Installation & User’s Guide” FFS 000-2145 for more information.

Line Program Error

Detected

Line An error has been detected in the

programming of the specied line.

Verify programming of line under the setup menu.

Line Pump Request

Ignored

Engineering The line has called for the pump

to be turned on but another

application is currently using the

STP

Verify that other applications are operating properly. Contact Franklin

Fueling Systems’ Technical Services Dept. for support.

Marginal Pass of Gross

Leak Test

Line The last passed gross test

detected a leak just under the

3 gph threshold.

Verify there is no sign of leaks within any of the sumps. Run

additional tests. Refer to “LS500 Auto Learn Line Leak Detection

Installation & User’s Guide” FFS 000-2145 for more information.

Monthly Leak Test Failed Line The Console has detected a line

leak greater than 0.2 gph.

Inspect all sumps for product. Refer to “LS500 Auto Learn Line

Leak Detection Installation & User’s Guide” FFS 000-2145 for more

information.

Not Enabled Line Line testing has not been enabled. Verify no other alarm is present then enter the line control menu and

enable the line testing feature.

Precision Leak Test Failed Line 0.1 GPH Line leak test failed. Follow site policy on line leak procedures.

Pressure Transducer Fail Line The transducer is not being

detected by the console.

Inspect the wiring to the specied transducer and the channel it

terminates at. Refer to “LS500 Auto Learn Line Leak Detection

Installation & User’s Guide” FFS 000-2145 for more information.

Sudden Pressure Loss Line During a 45 minute quite period

the pressure was seen to drop by

a 2 times the learned 3 gph slope.

Inspect all sumps for product. Refer to “LS500 Auto Learn Line

Leak Detection Installation & User’s Guide” FFS 000-2145 for more

information.

TPI Alarms

Displayed Alarm /

Warning

Device Description Recommended Actions

Capacitor Failing TPI The STP controller is reporting a

capacitor failure.

Refer to the applicable Smart controller Installation guide for details.

Clogged Intake TPI The STP controller has reported

a dry run condition but the

associated tank shows a product

level above the intake.

Ensure proper programming of the TPI and calibration of the Smart

Controller. If correct, check for an obstruction on the PMA.

Communication Failure TPI Communication from the TPI to

the STP controller has failed. The

Console is seeing the controller

but the controller is not responding

to commands.

Verify all wiring connections. Call FFS Technical Services Department

for support.

Controller Type Error TPI The programmed controller type

does not match what the console

is detecting.

Verify proper programming of the TPI as well as the Smart controller

type and address.

Dry Tank TPI The STP Controller has reported

a dry run condition and the

tank level is at or below the

programmed intake.

Ensure proper programming of the TPI and calibration of the Smart

Controller. If correct, add fuel.

Extended Run TPI The STP controller is reporting an

extended run condition.

Refer to the applicable Smart Controller Installation guide for details.

Hardware Fault TPI The STP controller is reporting

is reporting a hardware fault

condition.

High Temperature TPI The STP controller is reporting a

high temperature condition.

Locked Rotor TPI The STP controller is reporting a

locked rotor rating.

Not Calibrated TPI The STP controller is reporting

that it has not been calibrated.

Open Circuit TPI The STP controller is reporting an

open circuit condition.

Over Speed TPI The STP controller is reporting an

over speed condition.

Refer to the applicable Smart Controller Installation guide for details

Over Voltage TPI The STP controller is reporting an

over voltage condition.

1 2 ... 56 57 58 59 60 61 62 63 64 65 66

Comentários a estes Manuais

Sem comentários

Franklin-fueling-systems T5 Series Fuel Management System Programming Guide Manual do Utilizador Página 61

Comentários a estes Manuais

Manuais e produtos relacionados com Equipamento Franklin-fueling-systems T5 Series Fuel Management System Programming Guide