Franklin-fueling-systems T5 Series Fuel Management System Programming Guide Manual do Utilizador descarregar pdf (Página 56)

Displayed Alarm /

Warning

Device Description Recommended Actions

VFM No Data VRM

The Vapor Flow Meter is detected

but is not communicating with the

Console

Refer to Vapor Recovery Monitoring Alarm and Troubleshooting

identication guide 000-0529 for troubleshooting help.

Weekly Vapor Collection

Failure

VRM A Weekly Vapor Collection

Warning has occurred for 2

consecutive weeks.

Refer to Vapor Recovery Monitoring Alarm and Troubleshooting

identication guide 000-0529 for troubleshooting help.

Weekly Vapor Collection

Warning

VRM V / L average for Non-ORVR

transactions is greater than 1.32

or less than 0.81.

Refer to Vapor Recovery Monitoring Alarm and Troubleshooting

identication guide 000-0529 for troubleshooting help.

Weekly Ullage Pressure

Warning

VRM Ullage pressure is greater than

+1.3” WC for 5% of time.

Refer to Vapor Recovery Monitoring Alarm and Troubleshooting

identication guide 000-0529 for troubleshooting help.

Weekly Ullage Pressure

Failure

VRM A Weekly Ullage Pressure

Warning has occurred for 2

consecutive weeks.

Refer to Vapor Recovery Monitoring Alarm and Troubleshooting

identication guide 000-0529 for troubleshooting help.

Weekly Ullage Pressure

Leak Test Failure

VRM The leak rate of the vapor

recovery system is two times the

allowable rate as stated in TP-

201.3 for one week.

Refer to Vapor Recovery Monitoring Alarm and Troubleshooting

identication guide 000-0529 for troubleshooting help.

Weekly Ullage Pressure

Leak Test Warning

VRM A Weekly Ullage Pressure Leak

Test Warning has occurred for 2

consecutive weeks

Refer to Vapor Recovery Monitoring Alarm and Troubleshooting

identication guide 000-0529 for troubleshooting help.

Remote DTU is Ofine DTU The console cannot detect the

specied DTU.

Wrong ID Number

Dispenser Powered Off

Not installed correctly

Not on same phase voltage as console DTU

DTU FFS Interference DTU Two networks have the same

Network ID or nearby FFS

equipment is causing interference

with the system.

Verify Network ID programming in Setup Menu. DTU’s may be in

service at a nearby location that is causing interference. Contact

FFS Technical Services for support

DTU Non FFS

Interference

DTU Non-FFS equipment is causing

interference with the DTU signals.

Contact FFS Technical Services for support.

FMS Alarms

Alpha volume correction

error

Tank This error is caused by a

programming mistake in the

Special Products section.

Verify Special Product Alpha volume correction program parameters.

Contact FFS Technical Services Department for assistance.

API volume correction

error

Tank This error is caused by a

programming mistake in the

Special Products section.

Verify Special Product API volume correction program parameters.

Contact FFS Technical Services Department for assistance.

Correction table error Tank Level and Volume mismatch

detected in Correction table

programming.

Verify that all levels and volumes are entered accurately into the

Correction Table programming.

Density oat error Tank A communication error has

occurred involving the density

oat.

Verify programming and contact FFS Technical Services for support.

Density error Tank The density of the product is not

within specications.

Enter setup and verify the information under density in the probe

programming.

Float height error Tank This error could indicate that the

wrong oat type is installed or that

a programming error has occurred.

Review probe programming for proper oat type, number of oats in

the tank. (This would be an idea time to clean the probe and oats).

Float Missing Tank Probe detects a lesser number of

oats than programmed.

Review probe programming for correct number of oats. If correct

then inspect probe shaft, oats, and oat magnets. With the probes

out of the tank, this would be an idea time to clean the probe and

oats. If pressures meets requirements specied, contact Franklin

Fueling Systems’ Technical Services Dept. for support on this issue.

FMS conguration error None Conicts exist within FMS

Application programming.

Verify FMS setting are correct in accordance with the site

specications.

High product level Tank Product level exceeded High limit

set. Possible close to tank overll

condition

Acquire an accurate product level. If actual product level in tank does

not match the consoles displayed current level, verify programming is

correct.

High high product level Tank Product level exceeded High High

limit set. Possible tank overll

condition.

Acquire an accurate product level. If actual product level in tank does

not match the consoles displayed current level, verify programming is

correct.

1 2 ... 51 52 53 54 55 56 57 58 59 60 61 ... 65 66

Comentários a estes Manuais

Sem comentários

Franklin-fueling-systems T5 Series Fuel Management System Programming Guide Manual do Utilizador Página 56

Comentários a estes Manuais

Manuais e produtos relacionados com Equipamento Franklin-fueling-systems T5 Series Fuel Management System Programming Guide