Franklin-fueling-systems T5 Series Fuel Management System Programming Guide Manual do Utilizador descarregar pdf (Página 54)

Displayed Alarm /

Warning

Device Description Recommended Actions

Console DTU is ofine Slot The Console DTU is not

communicating with the Console

Check for proper wire connection between the console and the

Console DTU. Verify DTU input power. Replace DTU

Console DTU number

mismatch

Slot

The number of DTU Modules

detected does not match the

number programmed.

Ensure that a console DTU is being used. Possible bad bus

connection. Not powered. Replace DTU if connections and settings

check good.

Controller Module is

Ofine

Slot Controller Module is ofine due to

unknown causes.

Follow safety procedures before working inside the console. Visually

verify a steady green “Run” light. If red “Err” light is ashing or steady

try to reboot system. If the condition still exists, contact Franklin

Fueling Systems’ Technical Services Dept. for support on this issue.

DIM module number

mismatch

Slot DIM modules detected does not

match the number programmed.

Check that the number of DIM Modules installed matches the number

programmed under System Conguration > Modules Expected. If

problem persists, contact FFS Technical Services for support

Internal Error #1 System There is an internal buffer error

occurring in the gauge.

Contact FFS Technical Services for support

Invalid Conguration None The conguration that has been

loaded is not valid.

Verify the le type of the conguration which is being uploaded

Invalid Registration None The registration that is loaded is

not valid.

If you have upgraded the site before, use the upgrade tool to restore

the former registration. If you have not upgraded the site before,

contact FFS Technical Services for support.

IO Input Alarm None An input on the Input/Output

module has been congured as an

alarm and is active.

Check the programming and voltage inputs for the specied Input

channel on the IO module.

IO Module is ofine Slot The IO Module is not

communicating with the Console

Inspect the IO module for error lights. If green light is ashing,

recover the module. If the lights are off: Power down, remove / re-

seat the module and power back up. If problem persists, contact FFS

Technical Services for support

IO module number

mismatch

Slot IO Modules detected does not

match the number programmed.

Check that the number of IO Modules installed matches the num-

ber programmed under System Conguration > Modules Expected.

Check for a ashing green light or no light at all on the IO Module and

contact FFS Technical Services for support.

IS Barrier Violation None Non-Intrinsically Safe module

placed in IS area; or IS Barrier is

removed.

Check the module conguration to ensure that a module has not

been improperly placed. Power down and then remove / re-seat the IS

barrier. If problem persists contact FFS Technical Services for support

LON module number

mismatch

Slot Lon Modules detected does not

match the number of Lon Modules

programmed.

Check that the number of LON Modules installed matches the num-

ber programmed under System Conguration > Modules Expected.

If problem persists, contact FFS Technical Services for support.

Power Supply Input Alarm None An input on the Power Supply has

been congured as an alarm and

is active.

Check the programming and voltage inputs for the specied Low

Voltage Input channel on the Power Supply module.

Power Supply Module

number mismatch

Slot Power Supply Modules detected

does not match the number

programmed.

Check that the number of Power Supply Modules installed matches

the number programmed under System Conguration > Modules Ex-

pected. Check for a ashing green light or no light at all on the Power

Supply Module and contact FFS Technical Services for support

Power Supply Module is

Ofine

Slot Power Supply Module is ofine

due to unknown causes.

Follow safety procedures before working inside the console. Visually

verify a steady green “Run” light. If red “Err” light is ashing or steady

try to reboot system. If the condition still exists, contact Franklin

Fueling Systems’ Technical Services Dept. for support on this issue.

Power Supply Module

Setup Error

None Errors in the setup of the listed

module.

The console may need to be reprogrammed.

Printer Module Number

Mismatch

Slot Printer Modules detected does not

match the number programmed.

Check that the number of Printer Modules installed matches the

number programmed under System Conguration > Modules

Expected. If problem persists, contact FFS Technical Support.

Probe Module is Ofine Slot Probe Module is not

communicating with the console.

Follow safety procedures before working inside the console. Visually

verify a steady green “Run” light. If red “Err” light is ashing or steady,

re-seat module and reboot system. If the condition still exists, contact

Franklin Fueling Systems’ Technical Support for help on this issue.

Probe Module Number

Mismatch

Slot Probe Modules detected does

not match the number of Probe

Modules programmed.

Check that the number of Probe Modules installed matches the num-

ber programmed under System Conguration > Modules Expected.

Check for a ashing green light or no light at all on the Probe Module

and contact FFS Technical Services for support.

Probe Module Setup Error None Programming errors made during

setup of the Probe Module.

Verify Probe Module programming parameters. If the condition still

exists, contact Franklin Fueling Systems’ Technical Support for help

on this issue.

Relay Module is Ofine Slot Relay Module is ofine due to

unknown causes.

Follow safety procedures before working inside the console. Visually

verify a steady green “Run” light. If red “Err” light is ashing or steady

try to reboot system. If the condition still exists, contact Franklin

Fueling Systems’ Technical Support for help on this issue.

1 2 ... 49 50 51 52 53 54 55 56 57 58 59 ... 65 66

Comentários a estes Manuais

Sem comentários

Franklin-fueling-systems T5 Series Fuel Management System Programming Guide Manual do Utilizador Página 54

Comentários a estes Manuais

Manuais e produtos relacionados com Equipamento Franklin-fueling-systems T5 Series Fuel Management System Programming Guide