Franklin-fueling-systems T5 Series Fuel Management System Programming Guide Manual do Utilizador descarregar pdf (Página 53)

List of Alarms and Troubleshooting

For all alarms conditions, the troubleshooting steps provided in this chapter are suggested actions to take in the event of

an alarm. Follow all site policy procedures set by local governing agencies in the case of a spill, leak, or malfunction. If

the steps provided by this manual or the site policy are followed and the system still requires additional support, contact

Franklin Fueling Systems Technical Services.

Alarms are listed in sections for System Alarms, VRM Alarms, FMS Alarms, SCM Alarms, Wire Sensor Alarms, LLD

Alarms, TPI Alarms, Printer Alarms and Miscellaneous Alarms.

System Alarms

Displayed Alarm /

Warning

Device Description Recommended Actions

2-Wire Sensor Module is

Ofine

Slot 2-Wire Sensor Module is ofine

due to unknown causes.

Follow safety procedures before working inside of the console.

Visually verify a steady, green “Run” light. If a red “Err” light is ashing

or steady, try to reboot the system. If the condition still exists, contact

Franklin Fueling Systems’ Technical Services Dept. for support on

this issue.

2-Wire Sensor Module

Setup Error

None Programming errors made during

setup of the 2-Wire Sensor

Module.

Verify 2-Wire Sensor Module programming parameters. If the

condition still exists, contact Franklin Fueling Systems’ Technical

Services Dept. for support on this issue.

2-Wire Sensor module

number mismatch

Slot 2-Wire Sensor Modules detected

does not match the number

programmed.

At startup check that the number of 2-Wire Sensor Modules installed

matches the number programmed under System Conguration >

Modules Expected. On machines that are in service: Check for a

ashing green light or no light at all on the 2-Wire Sensor Module and

contact FFS Technical Services for support.

3-Wire Sensor Module is

Ofine

Slot 3-Wire Sensor Module is ofine

due to unknown causes.

Follow safety procedures before working inside of the console.

Visually verify a steady, green “Run” light. If a red “Err” light is ashing

or steady, try to reboot the system. If the condition still exists, contact

Franklin Fueling Systems’ Technical Services Dept. for support on

this issue.

3-Wire Sensor Module

Setup Error

None Programming errors made during

setup of the 3-Wire Sensor

Module.

Verify 3-Wire Sensor Module programming parameters. If the

condition still exists, contact Franklin Fueling Systems’ Technical

Services Dept. for support on this issue.

3-Wire Sensor Module

Mismatch

Slot 3-Wire Sensor Modules detected

does not match the number

programmed.

At startup check that the number of 3-Wire Sensor Modules installed

matches the number programmed under System Conguration >

Modules Expected. On machines that are in service: Check for a

ashing green light or no light at all on the 3-Wire Sensor Module and

contact FFS Technical Services for support.

4-20mA Module is Ofine Slot 4-20mA Module is ofine due to

unknown causes.

Follow safety procedures before working inside the console. Visually

verify a steady green “Run” light. If a red “Err” light is ashing or

steady, try to reboot system. If the condition still exists, contact

Franklin Fueling Systems’ Technical Services Dept. for support on

this issue.

4-20mA Module Number

Mismatch

Slot 4-20 mA Modules detected

does not match the number

programmed.

Check that the number of 4-20mA Modules installed matches

the number programmed under System Conguration > Modules

Expected. Check for a ashing green light or no light at all on the

4-20mA Module and contact FFS Technical Services for support

4-20mA Module Setup

Error

None Programming errors made during

setup of the 4-20mA Module.

Verify 4-20mA Module programming. If the condition still exists,

contact Franklin Fueling Systems’ Technical Services Dept.

4-20mA Input Error ChannelANA Errors have been detected in the

an analog input channel

If the input is not being used, set the programming to reect proper

input type. If the input is being used as an analog signal, inspect the

wiring and redo connections.

AC Input Module is Ofine Slot AC Input Module is ofine due to

unknown causes.

Follow safety procedures before working inside of the console.

Visually verify a steady green “Run” light. If a red “Err” light is ashing

or steady, try to reboot system. If the condition still exists, contact

Franklin Fueling Systems’ Technical Services Dept. for support on

this issue.

AC Input module number

mismatch

Slot AC Input Modules detected

does not match the number

programmed.

Check that the number of AC Input Modules installed matches

the number programmed under System Conguration > Modules

Expected. Check for a ashing green light or no light at all on the AC

Input Module and contact FFS Technical Services for support.

AC Input Module Setup

Error

None Programming errors made during

setup of the AC Input Module.

Verify AC Input Module programming parameters. If the condition still

exists, contact Franklin Fueling Systems’ Technical Services Dept. for

support on this issue.

AC Input Alarm None An input on the AC input module

has been congured as an

alarm and is active.

Check the programming and voltage inputs for the specied Input

channel on the AC Input module.

1 2 ... 48 49 50 51 52 53 54 55 56 57 58 ... 65 66

Comentários a estes Manuais

Sem comentários

Franklin-fueling-systems T5 Series Fuel Management System Programming Guide Manual do Utilizador Página 53

Comentários a estes Manuais

Manuais e produtos relacionados com Equipamento Franklin-fueling-systems T5 Series Fuel Management System Programming Guide