Franklin-fueling-systems TS-DTU Data Transfer Unit Dispenser Retrofit Manua Manual do Utilizador

Data Transfer UnitDispenser Retrofi t ManualModel TS-DTUFranklin Fueling Systems • 3760 Marsh Rd. • Madison, WI 53718 USATel: +1 608 838 8786 • 800 225

10Gilbarco Advantage Narrow Frame - DTU Installation26. Find reducer from IS wiring kit, 020-1513. From electrical enclosure, pull wires from potted

11Gilbarco Advantage Narrow Frame - DTU Installation36. Attach ring terminal of DTU ground wire to dispenser with bolt, nut and star washer.Figure 17:

12Gilbarco Encore 300 and 500 - DTU InstallationGilbarco Encore 300 and 500 SeriesThis section illustrates the basic components needed to retrofi t a T

13Gilbarco Encore 300 and 500 - DTU InstallationFigure 6: Connect Power Leads10. Find ground wire from power harness kit 600-0165. Remove ties and unc

14Gilbarco Encore 300 and 500 - DTU Installation24. Find straight conduit fi tting from IS wiring kit 020-1513. From electrical enclosure, pull wires f

15Gilbarco Encore 300 and 500 - DTU Installation34. Cut excess wire inside DTU allowing a length of 2” for terminal block wiring. Strip wire insulatio

16Tokheim Premier B DTU InstallationTokheim Premier B (422B)This section illustrates the basic components needed to retrofi t a TS-DTU module into an e

17Tokheim Premier B DTU Installation10. Using a ¾” conduit hole punch, open hole previously drilled. Figure 6: Use Hole Punch11. Find potted nipple

18Tokheim Premier B DTU Installation25. Remove nut and bushing from straight conduit fi tting. Place bushing on one end of fl exible conduit. Push wire

19Tokheim Premier B DTU Installation32. Route power cable along bottom of electrical enclosure and attach to AC power distribution board as shown. En

2Important Safety MessagesFranklin Fueling Systems (FFS)/Healy equipment is designed to be installed in association with volatile hydrocarbon liquids

20Tokheim Premier C DTU InstallationTokheim Premier CThis section illustrates the basic components needed to retrofi t a TS-DTU module into an existing

21Tokheim Premier C DTU Installation14. Remove nut from top of plug using wrench.15. Remove plug, washers, and nuts and discard all hardware.Figure 6:

22Tokheim Premier C DTU Installation28. Push bushing onto end of fl exible conduit and reattach to straight fi tting using nut.Figure 11: Flexible Condu

23Tokheim Premier C DTU InstallationFigure 16: Power Cable Installation36. Attach connector from the Tokheim power harness into available connector on

Wayne Ovation - DTU Installation24Wayne OvationThis section illustrates the basic components needed to retrofi t a TS-DTU module into an existing dispe

Wayne Ovation - DTU Installation25Figure 6: Attach Power Connector to Board 10. Pull wires away from door using positioning devices included with dis

Wayne Ovation - DTU Installation26Figure 10: Push Wire to Electrical Enclosure 21. Push top of potted nipple assembly through opening in electrical e

Wayne Ovation - DTU Installation2729. Push bushing onto end of fl exible conduit and reattach to straight fi tting using nut.Figure 14: Attach Flexible

28Wayne Vista 1 - DTU InstallationWayne Vista 1This section illustrates the basic components needed to retrofi t a TS-DTU module into an existing dispe

29Wayne Vista 1 - DTU InstallationFigure 5: Straight Conduit Installed15. Find TS-DTU/P kit and remove brackets, DTU, and hardware from box. 16. Remov

3ContentsImportant Safety Messages ...2Purpose: ...

30Wayne Vista 1 - DTU Installation25. Using wire nuts provided, connect all three white wires together. Connect three black wires together.Figure 10:

31Wayne Vista 1 - DTU Installation33. Attach wires to DTU terminal block as follows Figure 15: Wires Connected to DTU34. Reinstall barrier cover using

32Wayne Vista 2 - DTU InstallationWayne Vista 2This section illustrates the basic components needed to retrofi t a TS-DTU module into an existing dispe

33Wayne Vista 2 - DTU Installation13. From electrical enclosure, pull wires from the potted nipple assembly through opening of straight conduit. Attac

34Wayne Vista 2 - DTU Installation24. Using wire nuts provided, connect the incoming power, one end of the wire with the ferrite, and a wire for the D

35Wayne Vista 2 - DTU Installation32. Attach wires to DTU terminal block as follows Figure 16: Wires Connected to DTU33. Reinstall barrier cover using

36Wayne Vista 3 - DTU InstallationWayne Vista 3This section illustrates the basic components needed to retrofi t a TS-DTU module into an existing dispe

37Wayne Vista 3 - DTU InstallationFigure 5: Potted Conduit Installed12. Find reducer from IS conduit kit PN 020-1513. From electrical enclosure, pull

38Wayne Vista 3 - DTU Installation21. Find the incoming power connection on the dispenser power supply board shown in Figure 9Figure 9: Attach White C

39Wayne Vista 3 - DTU Installation30. Install the DTU assembly on the horizontal cross bracket as shown in Figure 14. Use the two screws, washers, an

4 General InformationPurpose:This procedure describes the tools, methods and skill levels required to install an INCON/Franklin Fueling Systems model

©2008 FFS 000-2146 rev B

5General InformationSpecifi cations: Power 100-240 VAC, 60 Hz, 0.25 A Parts ListThe TS-DTU and TS-DRK installation kit consists of the following m

6 General InformationGeneral Instructions Tools Required(This applies to all dispenser installation procedures) Assorted Open End Wrenches 1/4” throug

7General InformationConnecting the Vapor Flow Meter and Vapor Pressure SensorThe connection of potted nipple to the TS-VFM and TS-VPS in the lower sec

8Gilbarco Advantage Narrow Frame - DTU InstallationGilbarco Advantage Narrow FrameThis section illustrates the basic components needed to retrofi t a T

9Gilbarco Advantage Narrow Frame - DTU Installation9. Remove two screws from upper air gap knock-out cover and remove. Discard cover but keep screws