Franklin-fueling-systems T5 Tank Sentinel Programming Guide Manual do Utilizador descarregar pdf (Página 43)

Displayed Alarm /

Warning

Device Description Recommended Actions

Low battery Tank Backup battery is low. See Installation Guide for replacement instructions.

Low low product volume Tank/Manifold Product volume below Low

Low limit set. The tank or

manifold specied may be

close to empty.

Acquire an accurate product volume. If actual product volume in

tank does not match the consoles displayed current volume, verify

programming.

Low product volume Tank/Manifold Product volume below

Low limit set. The tank or

manifold specied may be

close to empty.

Acquire an accurate product volume. If actual product volume in

tank does not match the consoles displayed current volume, verify

programming.

Manifold Gross Leak

Detected

Manifold A Gross leak is detected in

the specied manifold

Review tank leak test history and programming. Refer to Section

5: Misc./ Tank Leak Tests – Type and Frequency for instructions on

manually starting line leak tests.

Manifold Leak Detected Manifold A leak is detected in the

specied manifold

Review tank leak test history and programming. Refer to Section

5: Misc./ Tank Leak Tests – Type and Frequency for instructions on

manually starting line leak tests.

Manifold SCALD Leak

Detected

Manifold SCALD software detected

a leak in the specied

manifold.

Review tank leak test history and programming. Review, why tank tests

fail.

Manifold Theft Detected Manifold Product used in Sentinel

Mode exceeds theft limit

set.

Verify theft limit in programming. Also obtain an accurate product level

and compare to inventory.

Marginal Pass of Gross

Leak Test

Line Gross test passed with

marginal results. May

be caused by thermal

instability of the line or a

leak.

Engineering

Modem Error None Indicates that a modem

malfunction has occurred.

Try to recycle power on the console. Verify modem programming. If

the alarm does not clear, contact Franklin Fueling Systems’ Technical

Services Dept. for support on this issue.

Monthly Leak Test Failed Line 0.2 GPH Line leak test

failed.

Follow site policy on line leak procedures.

Net error Tank Product net level exceeds

tank diameter due to

misconguration of

programming.

Verify tank, offset, and probe programming.

No data available Tank Engineering Engineering

No probe detected Tank Communications error

between probe and

console.

Verify correct probe programming. If problem still exists, suspect wiring

or faulty probe head.

Not Enabled Line Specied line not enabled. Verify programming.

Not Learned Line Specied line not learned. Verify programming. If necessary to learn line see TS-5 Series FMS

Installation Manual for TS-Ls500 AutoLearn Calibration instructions.

Open analog input Tank No analog input signal. Verify programming, if alarm is still present check wiring. If problem still

persists, suspect analog module to be at fault.

Power Supply Module is

Ofine

Slot Power Supply Module is

ofine due to unknown

causes.

Follow safety procedures before working inside the console. Visually

verify a steady green “Run” light. If red “Err” light is ashing or steady

try to reboot system. If the condition still exists, contact Franklin Fueling

Systems’ Technical Services Dept. for support on this issue.

Power Supply Module

Setup Error

None Errors in the setup of the

listed module.

The console may need to be reprogrammed.

Precision Leak Test Failed Line 0.1 GPH Line leak test

failed.

Follow site policy on line leak procedures.

Pressure Transducer Fail Line Leak Sensing Unit

(Transducer) sending

erroneous data to console.

Only FFS AutoLearn TS-Ls500 Transducers can be used with this

system for line leak detection. Verify line leak programming. Check

wiring continuity from LSU to console. If the condition still exists, contact

Franklin Fueling Systems’ Technical Services Dept. for support on this

issue.

Printer Paper Jam None Indicates that paper is

jammed in printer.

Carefully lift printer cover to inspect and remove the jammed paper.

Probe Module is Ofine Slot Probe Module is ofine due

to unknown causes.

Follow safety procedures before working inside the console. Visually

verify a steady green “Run” light. If red “Err” light is ashing or steady

try to reboot system. If the condition still exists, contact Franklin Fueling

Systems’ Technical Services Dept. for support on this issue.

1 2 ... 38 39 40 41 42 43 44 45 46 47 48

Comentários a estes Manuais

Sem comentários

Franklin-fueling-systems T5 Tank Sentinel Programming Guide Manual do Utilizador Página 43

Comentários a estes Manuais

Manuais e produtos relacionados com Equipamento Franklin-fueling-systems T5 Tank Sentinel Programming Guide